Ga direct naar productinformatie
1 van 6

SpeedyBee F405 Mini Flight Controller with BLS 35A Mini V2 20x20 4-in-1 ESC for RC FPV Racing Drone

SpeedyBee F405 Mini Flight Controller with BLS 35A Mini V2 20x20 4-in-1 ESC for RC FPV Racing Drone

Normale prijs €74,84 EUR
Normale prijs Aanbiedingsprijs €74,84 EUR
Aanbieding Uitverkocht
Inclusief btw.

SPECIFICATIONS

Brand Name: U-Angel-1988

Origin: Mainland China

Material: Metal

Recommend Age: 14+y

RC Parts & Accs: Gyros

Size: 20*20mm

For Vehicle Type: Airplanes

Use: Vehicles & Remote Control Toys

Upgrade Parts/Accessories: SpeedyBee F405 Mini Flight Controller

Remote Control Peripherals/Devices: ESC

Tool Supplies: Assembled class

Quantity: 1 pcs

Technical parameters: Value 2

Model Number: 35A ESC

Four-wheel Drive Attributes: SpeedyBee F405 Mini BLS 35A

Wheelbase: Screws

Choice: yes


Specifications

ProductName

SpeedyBee F405 V3 30x30 Flight Controller

MCU

STM32F405

IMU(Gyro)

ICM42688P

USB Port Type

Type-C

Barometer

Built-in

OSD Chip

AT7456E chip

BLE Bluetooth

Supported. Used to connect with the SpeedyBee App for flight controller and ESC parameter configuration. Please make sure the MSP switch on UART 4 is turned on and set to a baud rate of 115200, otherwise Bluetooth functionality will not be available.

Wireless FC Firmware Flashing

NOT Supported. Please connect to the Betaflight configurator on the PC to do FC firmeare update

Wireless Blackbox Dwonload & Analysis

NOT Supported. Please connect to the Betaflight configurator on the PC to do blackbox analysis.

WIFI

Not supported

DJI Air Unit Connection Way

Direct soldering

DJI Air Unit Compatibility

Compatible with all DJI Air Units: DJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1. Please use the solder pads < 9V, G, T1, R1, G, SUBS(R2) > on the front right corner of the flight controller to make a pin-to-pin connection with the solder pads on the DJI Air Unit. UART1(T1, R1) is used for OSD and SUBS(R2) is used for DJI Air Unit’s internal SBUS receiver signal input.

Blackbox

8MB Onboard Flash

BetaFlight Camera Control Pad

Yes(CC pad on the front side)

Current Sensor Input

Supported. For SpeedyBee BLS 35A V2 ESC, please set Scale=250 and Offset=-500.

Power Input

3-6S LiPo. The flight controller is powered through the G, V wires of the 8pin harness or G, V pads from the bottom side of the flight controller.

5V Output

4 groups of 5V output, three +5V pads and 1 BZ+ pad( used for Buzzer) on front side. The total current load is 2A.

9V Output

1 group of 9V output, one +9V pad on front side. The total current load is 3A.

3.3V Output

Supported. Soldering pad named ‘3V3’ on the front top of the flight controller. Designed for 3.3V input receivers. Up to 500mA current load.

4.5V Output

Supported. Designed for radio receiver and GPS module even when the FC is powered through the USB port. Up to 1A current load.

ESC Signal

M1 - M4 wires or soldering pads on bottom side.

UART

6 sets(UART1, UART2, UART3, UART4(Dedicated for Bluetooth connection)), UART5(Dedicated for ESC telemetry),UART6

ESC Telemetry

UART R5(UART5)

I2C

Supported. DA & CL pads on front side. Used for magnetometer, sonar, etc

Traditional Betaflight LED Pad

Supported. 5V, G and LED pads on bottom of the front side. Used for WS2812 LEDs controlled by the Betaflight firmware.

Buzzer

BZ+ and BZ- pad used for 5V Buzzer

BOOT Button

Supported. Press and hold BOOT button and power the FC on at the same time will force the FC to enter DFU mode, this is for firmware flashing when the FC gets bricked.

RSSI Input

Not Supported

Smart Port / F.Port

Not Supported

Supported Flight Controller Firmware

BetaFlight(Default), INAV

Firmware Target Name

SPEEDYBEEF405MINI

Mounting

20 x 20mm 3.5mm hole diameter ,Compatible with M2 and M3 screws/Silicone grommets.

Dimension

30(L) x 32(W) x 7.8(H)mm

Weight

9.6g

ProductName

SpeedyBee 35A BLHeli_S Mini V2 4-in-1 ESC

Firmware

BLHeli_S J-H-40

Continuous Current

35A * 4

Burst Current

45A(5seconds)

ESC Protocol

DSHOT300/600

Power Input

3-6S LiPo

Power Output

VBAT(Battery voltage, used to power the flight controller)

Current Sensor

Support (Scale=250 Offset=-500)

Mounting

20 x 20mm ∅3.5mm hole size,compatible with M2 and M3 screws/Silicone grommets.

Dimension

35 * 35 * 5.5mm

Weight

7.2g

Specs Overview

Product Name

SpeedyBee F405 Mini BLS 35A 20x20 Stack

Flight Controller

SpeedyBee F405 Min

ESC

SpeedyBee BLS 35A Mini V2 4-in-1 ESC

Bluetooth

Supported. Used to connect with the SpeedyBee App for flight controller and ESC parameter configuration. Please make sure the MSP switch on UART 4 is turned on and set to a baud rate of 115200, otherwise Bluetooth functionality will not be available.

WiFi

NOT Supported

Wireless FC Firmware Flashing

NOT Supported

Wireless Blackbox Dwonload & Analysis

NOT Supported

Power Input

3-6S LiPo

Mounting

20 x 20mm 3.5mm hole size,Compatible with M2 and M3 screws/Silicone grommets

Dimension

32mm(L) x 35mm(W) x 14.2mm(H)

Weight

13.5g






Product features

Materials and care

Merchandising tips

Alle details bekijken
Je winkelwagen
Variant Totaal variant Aantal Prijs Totaal variant
48666982121820
FC and ESC14:29#FC and ESC
FC and ESC14:29#FC and ESC
€74,84/st
€0,00
€74,84/st €0,00